About RomerGRBE

Results of the work in the Laser4Fun project has been published as:

Alfredo I. Aguilar-Morales, Sabri Alamri, Bogdan Voisiat, Tim Kunze and Andrés F. Lasagni. Nano-Roughness on the Wettability Performance of Microstructured Metallic Surface Using Direct Laser Interference Patterning. Materials 2019, 12(17), 2737.

Abstract

Superhydrophobic natural surfaces usually have multiple levels of structure hierarchy, particularly microstructures covered with nano-roughness. The multi-scale nature of such a surface reduces the wetting of water and oils, and supports self-cleaning properties. In this work, in order to broaden our understanding of the wetting properties of technical surfaces, biomimetic surface patterns were fabricated on stainless steel with single and multi-scale periodic structures using direct laser interference patterning (DLIP). Micropillars with a spatial period of 5.5 µm and a structural depth of 4.2 µm were fabricated and covered by a sub-micro roughness by using ultrashort laser pulses, thus obtaining a hierarchical geometry. In order to distinguish the influence of the different features on the wettability behavior, a nanosecond laser source was used to melt the nano-roughness, and thus to obtain single-scale patterns. Then, a systematic comparison between the single- and multi-scale structures was performed. Although, the treated surfaces showed hydrophilic behavior directly after the laser treatment, over time they reached a steady-state hydrophobic condition. However, the multi-scale structured metal showed a contact angle 31° higher than the single-scale geometry when the steady-state conditions were reached. Furthermore, the impact of the surface chemistry was investigated by energy dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) analyses. Finally, a hydrophobizing agent was applied to the laser treated samples in order to further enhance the water contact angles and to determine the pure contribution of the surface topography. In the latter case, the multi-scale periodic microstructures reached static contact angles of 152° ± 2° and a contact angle hysteresis of only 4° ± 2°, while the single-scale structures did not show superhydrophobic behavior. These results definitely suggest that multi-scale DLIP structures in conjunction with a surface chemistry modification can promote a superhydrophobic regime.

Link

https://doi.org/10.3390/ma12172737

Results of the work in the Laser4Fun project has been published as:

Romano, J.M., Helbig, R., Fraggelakis, F., Garcia-Giron, A., Werner, C., Kling, R., Dimov, S., Springtail-Inspired Triangular Laser-Induced Surface Textures on Metals Using MHz Ultrashort Pulses. J. Micro Nano-Manuf  2019, 7(2), 024504. 

Abstract

Considering the attractive surface functionalities of springtails (Collembola), an attempt at mimicking their cuticular topography on metals is proposed. An efficient single-step manufacturing process has been considered, involving laser-induced periodic surface structures (LIPSS) generated by near-infrared femtosecond laser pulses. By investigating the influence of number of pulses and pulse fluence, extraordinarily uniform triangular structures were fabricated on stainless steel and titanium alloy surfaces, resembling the primary comb-like surface structure of springtails. The laser-textured metallic surfaces exhibited hydrophobic properties and light scattering effects that were considered in this research as a potential in-line process monitoring solution. The possibilities to increase the processing throughput by employing high repetition rates in the MHz-range are also investigated.

Link(s)

• https://doi.org/10.1115/1.4043417

Results of the work in the Laser4Fun project has been published as:

Tobias Stark , Thomas Kiedrowski, Holger Marschall and Andrés Fabián Lasagni. Avoiding Starvation in Tribocontact Through Active Lubricant Transport in Laser Textured Surfaces. Lubricants 2019, 7(6), 54.

Abstract

Laser texturing is a viable tool to enhance the tribological performance of surfaces. Especially textures created with Direct Laser Interference Patterning (DLIP) show outstanding improvement in terms of reduction of coefficient of friction (COF) as well as the extension of oil film lifetime. However, since DLIP textures have a limited depth, they can be quickly damaged, especially within the tribocontact area, where wear occurs. This study aims at elucidating the fluid dynamical behavior of the lubricant in the surroundings of the tribocontact where channel-like surface textures are left after the abrasion wear inside the tribocontact area. In a first step, numerical investigations of lubricant wetting phenomena are performed applying OpenFOAM. The results show that narrow channels (width of 10 μm) allow higher spreading than wide channels (width of 30 μm). In a second step, fluid transport inside DLIP textures is investigated experimentally. The results show an anisotropic spreading with the spreading velocity dependent on the period and depth of the laser textures. A mechanism is introduced for how lubricant can be transported out of the channels into the tribocontact. The main conclusion of this study is that active lubricant transport in laser textured surfaces can avoid starvation in the tribocontact.

Link(s)

• https://www.mdpi.com/2075-4442/7/6/54/hthttps://www.mdpi.com/2075-4442/7/6/54/htmm
• https://doi.org/10.3390/lubricants7060054

Results of the work in the Laser4Fun project has been published as:

Storm, S., Alamri, S., Soldera, M., Kunze, T., Lasagni, A. F., How to Tailor Structural Colors for Extended Visibility and White Light Generation Employing Direct Laser Interference Patterning. Macromol. Chem. Phys. 2019, 1900205. 

Abstract

The appearance of a surface can be controlled by creating periodic microstructures designed to diffract light and produce structural colors. Nevertheless, since structural coloration is based on diffraction, the produced colors have a strong dependence on the viewing angle and absence of coloration takes place while tilting the samples. In this work direct laser interference patterning is used to firstly provide transparent polymer sheets a structural coloration with a high‐range observation angle, and secondly to demonstrate the combination of structural colors, producing a white coloring effect. The employed approaches are based on the fabrication of micro‐gratings with multiple periods in the same structured area and on the engineering of the diffraction orders of the diffraction spectrum. The patterned surfaces are characterized by confocal microscopy and angular spectrometry in reflection mode. The morphological characterization shows homogeneous surface patterns, while the spectral results demonstrate that combining four spatial periods on a single patterned surface, a white appearance is obtained over an angular observation range higher than 30°. The experimental results are supported by theoretical predictions by means of generalized formulas based on the diffraction of light.

Link(s)

• https://doi.org/10.1002/macp.201900205